RayKol Auto EVA 12 is a nitrogen blow-down automated evaporation system that provides automated evaporation of up to 12 samples in parallel with endpoint detection. This automated evaporation system uses vortex airflow generated from stable angled nitrogen blow, to constantly dis
Raykol Group(XiaMen)Corp.,Ltd. [2022-11-23 14:45:35 ]
ASPE Ultra series Automated Solid Phase System is an automated sample preparation system designed for analysis of organic substances in water samples, including drinking water, tap water, underground water, surface water as well as wastewater. RayKol ASPE Ultra automate liquid li
Raykol Group(XiaMen)Corp.,Ltd. [2022-11-23 14:45:04 ]
Automated laboratory equipment is increasingly becoming in demand as laboratories require for higher throughput and automation. These lab automation equipment are optimized and automated from conventional sample preparation techniques, and designed to increase laboratory producti
Raykol Group(XiaMen)Corp.,Ltd. [2022-11-23 14:44:13 ]
With compact size, and high accuracy, the pull push meter is easy to operate and handy to carry out. The digital push-pull force gauge, also called the digital push-pull force meter, can be widely applied in electron, high & low voltage electrical appliances, hardware, automobile
Mikrometry instruments limited [2022-10-21 14:57:33 ]
Electromagnetic detection is a very important non-destructive testing method and is widely used. Mag flux testing is a magnetic method of nondestructive testing that is used to detect corrosion and pitting in steel structures, most commonly pipelines and storage tanks. The basic
Nanjing BKN Automation System Co.,LTD [2022-09-28 14:22:28 ]
Stimulating the coil makes a magnetic induction to the tested material. The induced electromotive force received by the testing coil is related to the shape and size of the material hysteresis loop. When the low-frequency sinusoidal wave excitation voltage is magnetically induced
Nanjing BKN Automation System Co.,LTD [2022-09-28 14:20:55 ]
The aluminum tube is a type of non-ferrous metal which may have one or more closed holes which are thick and uniform in cross-section. It is widely used in electrical, agricultural, electromechanical and other industries. Therefore, when using aluminium tubes, we need to test the
Nanjing BKN Automation System Co.,LTD [2022-09-28 14:20:28 ]
GSET-551 Steel Wire Eddy Current Flaw Detector Brief Introduction Using the eddy current signal processing method and high-performance DSP algorithm, the NDT wire rope tester detection ability of micro-crack is as high as 0.05mm deep crack. Using computer digital technology and \
Nanjing BKN Automation System Co.,LTD [2022-09-28 14:20:02 ]
Ndt inspection equipment is widely used in industry, such as nuclear industry, weapon manufacturing, machinery industry, shipbuilding, petrochemical industry, railway and high-speed train, automobile, boiler and pressure vessel, special equipment, customs inspection, etc. Many pr
Nanjing BKN Automation System Co.,LTD [2022-09-28 14:19:32 ]
OTC200 optical tool setter/optical tool presetter is a wireless tool setter, optical coded signals are used to transmit information between the CNC tool setter and the receiver. It mainly used in various specifications of small to medium machining centers, CNC milling machines, d
Harbin Pioneer M&E Technical Development Co., Ltd [2022-09-20 11:10:36 ]
1. The reason why the dynamic diameter of the touch trigger probe is smaller than the static diameter After learning about the principle of probe calibration, we can easily explain why the dynamic diameter of the probe stylus is smaller than the static diameter. (1) The touch tri
Harbin Pioneer M&E Technical Development Co., Ltd [2022-09-20 11:08:01 ]
Specs of Low Speed Refrigerated Centrifuge KDC-2046 Microcomputer control with digital display. Driven by AC frequency conversion motor with quiet and clean running. Imported refrigeration compressor 9 kinds of ascending and descending rate of choice 10 kinds of custom work mode
ANHUI USTC Zonkia Scientific Instruments Co., LTD [2022-09-13 14:57:56 ]
Specs of Low Speed Centrifuge SC-3614/SC-3616 Microcomputer control, LCD liquid crystal display(LCD) AC frequency conversion motor drive, quiet operation clean. Brushless DC step-less speed regulating motor. Offers 10kinds ascending and descending rate selection mode, Offer 9 kin
ANHUI USTC Zonkia Scientific Instruments Co., LTD [2022-09-13 14:56:46 ]
Specs of Low Speed Centrifuge SC 3610 SC-3612 Microcomputer control, LCD liquid crystal display(LCD) AC frequency conversion motor drive, quiet operation clean. Brushless DC step-less speed regulating motor. Offers 9 kinds ascending and descending rate selection mode, Offer 10 ki
ANHUI USTC Zonkia Scientific Instruments Co., LTD [2022-09-13 14:56:05 ]
Specs of Low Speed Centrifuge KDC-1046 Microcomputer control, LCD liquid crystal display(LCD) AC frequency conversion motor drive, quiet operation clean. Offers nine ascending and descending rate selection mode, Offer ten kinds of working mode selection, can free programming call
ANHUI USTC Zonkia Scientific Instruments Co., LTD [2022-09-13 14:55:01 ]
The low-speed centrifuge is widely used for separating lab solutions and particles. Popular in places like hospital blood banks and blood processing centres, it is ideal for analyzing biological samples. The low-speed centrifuge is adaptable to various rotor configurations such a
ANHUI USTC Zonkia Scientific Instruments Co., LTD [2022-09-13 14:54:23 ]
Model Number UIYCA10AS18A20 Frequency Range DC-18GHz Power 10W Attenuation Value 20dB Attenuation Tolerance ±0.8dB VSWR 1.3 Connector Type SMA-M/SMA-F Impedance 50Ω
UIY Inc. [2022-09-07 15:40:23 ]
Functions TPL-3C 2M transmission analyzer is a multi-functional and full-featured digital tranmission system test device, design for the installation test, engineering check and acceptance, daily maintenance of digital networks, mainly performing channel test, alarm analysis, fau
Shanghai Grandway Telecom Tech.Co.,Ltd. [2022-09-07 15:05:47 ]
ETTA Advanced Digital Torque Indicator Mikrometry digital push pull force gauge is a designed with our torque senser. This digital torque indicators are main used in testing and calibrating tighten force, parts torsional destructive testing, etc. With features of simple operation
Mikrometry instruments limited [2022-08-24 16:20:00 ]
ETIPD Leeb Hardness Testing Mikrometry digital hardness meter ETIPD is a kind of portable measuring tool; the leeb tester can be quick, nondestructive, and high accuracy when measuring common metal materials hardness. The Leeb hardness tester can be used in the laboratory, as wel
Mikrometry instruments limited [2022-08-24 16:16:55 ]
