Testing Equipment Manufacturers and Suppliers
Function Determination of whether the safety glazing material has a certain minimum strength and cohesion under impact from a small hard object Suitable for impact test of safety glass and tempered glass. Related Standard ISO 3537Road vehicles — Safety glazing materials — Me
Qinhuangdao Yuanchen Technology Equipment Co., Ltd. [2020-05-20 13:53:15 ]
Function Determining the effect of exposure of safety glazing materials to temperature and humidity condition by boiling. Related Standard EN ISO 12543 – 4 Glass in building -Laminated glass and laminated safety glass – Part 4 Test methods for durability – Clause 5 High-te
Qinhuangdao Yuanchen Technology Equipment Co., Ltd. [2020-05-20 13:32:02 ]
Reference standard BS EN 12600 2002 Glass in building – Pendulum test – Impact test method and classification for flat glass Technical Data Weight 50 kg ± 0,1 kg Tyre pressure 0.35Mpa ± 0.02Mpa Tyre Type 3.50-R8 4PR Sample size 876 mm ± 2 mm * 1938 mm ± 2 mm Inside the
Qinhuangdao Yuanchen Technology Equipment Co., Ltd. [2020-05-20 13:19:07 ]
1. Different types of curves can be created by software base on user definition. (Voltage-time curve, current-time curve, capacity-voltage curve, loops times charge/discharge capacity curve, loops times charge/ discharge efficiency curve, etc) 2. Data reports are created by the s
Neware Technology Limited [2020-05-11 15:41:55 ]
This\'s an eight-channel battery analyzer to analyze small coin cells and cylindrical batteries from 5.0 mA to 6000 mA, up to 5V, with gold-plated pins for the best connection. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be
Neware Technology Limited [2020-05-11 15:23:45 ]
1. Features By using the compressed air as the power source, the output liquid pressure and the pressure of the driving air source pressure is in proportionality. By adjusting the pressure of the inlet air source, the corresponding liquid pressure can be obtained. When the air pr
JINAN ODMT FLUID CONTROL EQUIPMENT CO., LTD. [2020-04-29 15:02:29 ]
ODMT MPGC series pressure gauge calibration table is applicable for testing spring tubes (C-type tube, coil spring tube, spiral tube), etc. The calibration pressure of pneumatic calibration table is up to 15Mpa and that of hydraulic calibration table is up to 250Mpa. (Customers c
JINAN ODMT FLUID CONTROL EQUIPMENT CO., LTD. [2020-04-29 14:54:08 ]
ASTM F2100 /2101 Test Standard Bacterial Filtration Efficiency Tester Of Medical Face Mask is applied to test the filtration efficiency of mask, can be used in metering calibration department, scientific research institution, mask manufacturer and other related departments. Stand
stgoup [2020-04-18 11:15:45 ]
Water Vapour Permeability Tester, is to determine the water vapour permeability of various textile and garment fabric, coating fabric, composite, sportswear and industrial fabrics. This Vapour permeability testing machine is also suitable for conducting the Moisture Vapor Transmi
stgoup [2020-04-11 11:44:25 ]
Face Mask Differential Pressure Tester is used for face mask air flow resistance and differential pressure testing to check breathability and can also be used to check differential pressure of textile materials gas exchanger. Standards EN 149, EN 14683, ASTM F2100, MIL-M-36954C,G
stgoup [2020-04-11 09:49:25 ]
BFE Bacterial Filtration Efficiency Tester is applied to test the filtration efficiency of mask, can be used in metering calibration department, scientific research institution, mask manufacturer and other related departments. Standards NIOSH 42 CFR Part 84 NIOSH Respiratory User
stgoup [2020-04-11 09:47:47 ]
Melt-blown fabric and mask automatic filter performance tester uses the most advanced technology and design concepts, to meet a variety of test standards and the latest National standard GB / T 32610.Only relatively little operation is required to complete all the function and op
stgoup [2020-04-11 09:46:34 ]
Standard BS EN136-1998 Respiratory protective devices -Full face masks - Requirements testing, marking GB 19083-2010 Technical requirements of medical protective masks YY 0469-2011 Technical requirements of medical surgical masks-Blood penetration test device GB 2626-2006 Respir
stgoup [2020-04-11 09:45:31 ]
The textile airflow resistance tester is used to determine the anti-penetration properties of ordinary fabrics and medical protective masks to airflow at a constant flow rate . It is mainly used for the determination of air penetration of textiles ,cotton, and space cotton. The t
stgoup [2020-04-11 09:31:26 ]
Spray Rating Tester is designed to determine the surface wetting resistance of any fabrics, which may or may not have been given a water-repellent finish. It is not intended to predict waterproofness, since it does not measure the penetration of water through fabric. Standards IS
stgoup [2020-04-11 09:29:56 ]
Ball Drop Impact Test Machine Drop Ball Impact Specimen Support and Frame for Laminated Glass Related Standard ISO 3537 Road vehicles — Safety glazing materials — Mechanical tests – Clause 6 227 g ball test, Clause 7 2260 g ball test GB 15763.3 Safety glazing materials in b
Qinhuangdao Yuanchen Technology Equipment Co., Ltd. [2020-04-10 15:47:49 ]
Pummel Test Equipment for Laminated Glass Pummel Test Device Application Pummel test equipment for detect the adhesion of the interlayer of the laminated glass. Data Hammer head diameter 30mm Impact Distance Adjustable Voltage 380v Whole machine voltage 0.80KW Test machine size 1
Qinhuangdao Yuanchen Technology Equipment Co., Ltd. [2020-04-10 15:43:27 ]
Standards NIOSH 42 CFR Part 84 NIOSH Respiratory User Notices 42 CFR Part 84 Respiratory Protective Devices. EN 134 Respiratory protective devices - Nomenclature of components JMOL Japan protective mask standard. GB 19083 Technical requirement of medial protective mask. GB2626 Se
stgoup [2020-04-09 21:56:41 ]
The handheld brinell hardness tester 3000kgf test force with 10mm ball indenter 1580kgf test force with 7.26mm ball indenter 500kgf test force with 2.5mm ball indenter 187.5/62.5kgf test force with 2.5mm/5mm ball indenter Test range can be from 32 HBW to 650 HBW. Test force error
ShenZhen Xinzhibang Inst. & Eqpt. Co., Ltd [2020-04-08 15:38:39 ]
It is used to test the percentage of materials containing bacteria suspended particles at the specified flow rate. The dual gas path simultaneous comparison sampling method is used to improve the accuracy of sampling, which is suitable for the performance testing of bacterial fil
Qinsun Instruments (Shanghai) Co., Ltd. [2020-04-07 16:21:07 ]
