water pump pressure - Manufacturers, Suppliers & Exporters
1. The maximum lift of the rubber-lined impeller should not exceed 63m. The maximum allowable linear speed should not exceed 30m/m. 2. Bearings generally use rolling bearings and are lubricated with thin oil or grease. Their operating temperature should not exceed 75°C. 3. The p
Pansto Pump Co., Ltd [2024-03-29 15:22:32 ]
Although the O-ring for sealing the slurry pump is a very small accessory in the entire assembly of the slurry pump, its role is irreplaceable. Today we will talk about its characteristics. As for the O-ring used for reciprocating motion, its motion friction resistance is smaller
Pansto Pump Co., Ltd [2024-03-29 14:25:20 ]
The most common daily maintenance for slurry pumps is to pay more attention to maintenance during operation. 1. Pay attention to changes in the meter pointer. Under normal operation, the position of the instrument pointer should be basically stable at a certain position. If the i
Pansto Pump Co., Ltd [2024-03-27 10:18:44 ]
The ZJ series slurry pump is also the most common slurry pump nowadays. It is a single-stage, single-suction, centrifugal horizontal slurry pump. This series of slurry pumps are divided into various specifications according to the outlet size 350mm, 300mm, 250mm, 200mm, 150mm, 10
Pansto Pump Co., Ltd [2024-03-29 14:40:02 ]
The O-type sealing ring is a rubber sealing ring with a circular cross-section. Because its cross-section is O-shaped, it is called an O-type rubber sealing ring, also called an O-ring. It began to appear in the mid-19th century, when it was used as a sealing element for steam en
Pansto Pump Co., Ltd [2024-03-29 14:27:57 ]
When analyzing the energy consumption under different adjustment methods, the article only analyzes the two widely used adjustment methods valve adjustment and pump variable speed adjustment. Since the purpose of parallel and series operation of centrifugal pumps is to increase t
Pansto Pump Co., Ltd [2024-03-29 15:19:43 ]
One type of shaft seal for slurry pumps is mechanical seals, but mechanical seals are divided into cartridge mechanical seals and non-cartridge mechanical seals. Today we will talk about the differences between these two types of machinery. Cartridge mechanical seals combine all
Pansto Pump Co., Ltd [2024-03-29 14:37:39 ]
The ZJ series slurry pump is suitable for transporting solid-liquid mixtures that are highly abrasive and contain hard solid particles. For example slurry, ash, coal washing plant, cement slurry, gravel, etc. ZJ series slurry pump is a new type of high-efficiency, energy-saving a
Pansto Pump Co., Ltd [2024-03-29 14:36:33 ]
The motors equipped with ZJ slurry pumps are generally ordinary asynchronous motors. When designing, the main performance parameters considered are overload capacity, starting performance, efficiency and power factor. As for the variable frequency motor, since the critical slip i
Pansto Pump Co., Ltd [2024-03-29 14:38:15 ]
The O-rings of horizontal slurry pumps can be divided into static seals, reciprocating seals, rotating seals and switch seals according to the relative movement state between the seal and the sealed device. According to the compression amount (tightness) of the O-ring compression
Pansto Pump Co., Ltd [2024-03-29 14:26:36 ]
The common series of submersible slurry pumps produced by our factory include SP series and ZJL series. The SP series is further divided into SP and SPR. SP means that the flow parts are made of high chromium alloy, and SPR means that the parts below the flow parts and the mounti
Pansto Pump Co., Ltd [2024-03-29 15:20:21 ]
There is a correct gap value between the impeller and the rear guard plate of the slurry pump. We have previously introduced the method of adjusting the impeller clearance of the AH slurry pump. Today we will introduce how to adjust the impeller clearance of ZJ slurry pump. Becau
Pansto Pump Co., Ltd [2024-03-29 14:41:16 ]
AH type slurry pumps are commonly made of two materials high chromium alloy and natural rubber. Today we are going to talk about slurry pumps made of natural rubber. Rubber slurry pumps are also called rubber-lined slurry pumps. They are characterized by corrosion resistance. Thi
Pansto Pump Co., Ltd [2024-03-29 15:20:55 ]
Various problems will be encountered during the use of slurry pumps. Today we are talking about the reasons and solutions for the heating of the slurry pump body. 1. Incorrect selection of the slurry pump results in a mismatch between the pump and the motor, resulting in heat gen
Pansto Pump Co., Ltd [2024-03-29 15:17:27 ]
Is there any difference between the impeller of our ZJ series slurry pump and the impeller of AH series slurry pump? Let’s find out today. The impellers of our ZJ series slurry pumps, regardless of model size, have a common feature, that is, their channels are relatively narrow
Pansto Pump Co., Ltd [2024-03-29 14:39:32 ]
The horizontal slurry pump ZJ series is one of our flagship products. It is characterized by high lift and can be directly connected to the coupling by cutting the impeller. So what kind of slurry is it suitable for transporting? Let’s talk today. The flow-passing parts of the
Pansto Pump Co., Ltd [2024-03-29 14:35:54 ]
The impeller is the main accessory of the slurry pump. The pumping of the slurry pump is entirely achieved by the rotation of the impeller. Today we will introduce the accessory impeller of the slurry pump. The slurry pump impeller is a rotating blade with a curved shape. The bla
Pansto Pump Co., Ltd [2024-03-27 10:17:42 ]
We have introduced the difference between ZJL and SP slurry pumps before. Both series of slurry pumps are vertical slurry pumps. So what are the similarities between them? Today we will introduce them. 1. They are both vertical slurry pumps, also known as submersible slurry pumps
Pansto Pump Co., Ltd [2024-03-29 14:34:29 ]
We have two series of submersible slurry pumps, one is the ZJL series and the other is the SP series. Both series are vertical installations. So what are the differences between these two pumps? Today Shijiazhuang Pansto Pump Industry will let you know one time. 1. First of all,
Pansto Pump Co., Ltd [2024-03-29 14:31:55 ]
When our fine sand recovery pumps are initially designed, we usually have one extra pump as a backup pump. So if the backup pump is never used, should it be left there forever? Of course not, our backup pump also needs to be cranked regularly. Let’s take a look at the role of r
Pansto Pump Co., Ltd [2024-03-29 15:16:44 ]
