Note: The XL rail key can be changed to accommodate several varieties of mounting rails. Remove the rail key screw with a 7/64th hex wrench and pull the rail key from the body. Insert the new rail key and fasten it in place with the rail key screw.
XL PARTS
Note: always avoid aggressive cleaning solutions as they may damage the XL.
The XL rail clamp tensioning bolt requires an application of high quality gun oil to keep it rust free. Use a soft cloth and mild detergent to clean the glass LED lens and keep it free of dirt and grime. The laser aperture (XL-2LL) can be cleaned with a Q-tip 9or similar item) and mild detergent.
MAINTENACE
5. Check for fit and tighten tension bolt until the XL is securely attached to the firearm.
4. Slightly depress the tension bolt to open the rail lamp, rotate the XL into place and release the pressure on the tension bolt to snap the light in place.
3. Angle the XL, placing the fixed portion of the rail clamp against the accessory rail and align the rail key with the appropriate cross groove in the accessory rail.
2. Loosen the rail clamp tension bolt.
1. The XL is design to be quickly attached or detached from the side of the weapon or accessory rail.
Make sure that the firearm is unloaded and the breech is open. It is imperative that safety measures by employed at all times while handling the firearm.
MOUNTING/REMOVAL PROCESURE
6. Swing the door latch over the door and snap it into place.
5. Firmly push and hold the door closed against the flashlight body.
4. Hold the battery switch/door at an angle and place the small tab on the bottom of the battery/door switch into the slot in the flashlight body.
3. Insert the new batteries observing polarity. Note: The flashlight is polarity protected and will not light if the batteries are inserted incorrectly.
2. Slip the batteries from the flashlight.
1. Unclip the door latch, the latch is tight, it may help to use a coin.
To access the battery compartment you must first remove the flashlight from the firearm. Follow the XL removal procedure instructions to remove the flashlight from the firearm.
DANGER: DO NOT use anything other than a CR-123 battery or rechargeable batteries with this product.
The ES-XL-2LL laser sights use 2 CR-123 (6V) batteries. The CR-123s negative and positive pole has been indicated on the mount.
BATTERY ASSEMBLY
If mounted to the side, the bullet will also deviate to the side of the laser line, as well as up and down. In practice, a XL-2LL on a handgun can be adjusted to keep the bullet strike within about 2 high and 2 low out to about 100 feet.
Laser adjustment and the muzzle velocity of the bullet determine where this point occurs. The user must decide how high above or below the sight line the bullet can be allowed to strike and adjust the sight accordingly. At distances less than the zero range the bullet will be above the sight line. Beyond the zero range the bullet will be the sight line.
For a laser mounted below or to the side of the bore, there is only one distance where the bullet path will coincide with the laser sight line, this point is the zero range.
LASER SIGHT ZEROING
Adjustable mount flexibility that can accommodate the Glock or Picatinny (1913) accessory rails.
Fits existing light bearing holsters
Machined anodized aluminum housing
Ambidextrous Momentary/Steady on-off Switch
Dust and Shockproof
Safe and adjustable
Compact
Lightweight
Quick target acquisition
FEATURES
Master Carton: Top cardboard carton
Unit package: Gift paper box
Packing: 1 unit/gift box, 50 units/master carton
PACKING
User manual
2 CR-123A lithium batteries
Calibration tools
Laser sight and LED Flashlight integrated group
KIT INCLUDES
Rail Mount: Integrated mount
Operation: Ambidextrous Momentary/Steady on-off Switch
Finish: Anodic oxidation/ V' r3 black
Construction: Aircraft aluminum 7061-T6
Warranty: Extended Warranty
Weight with Battery: 4.72 oz, 133.8g
Working volt: 3V
Life time:
Strobe red laser sight with led flashlight
1.Red laser of 5mw 650nm
2.200 LM CREE Q5 led flashlight
3.Normal or hard anodize
Delivery Time: | 20-30 days for MOQ qty, 50-60 days for 1k pcs or OEM order |
Package: | Packing: 1 unit/gift box, 50 units/master carton, Gift box size: 160X110X70mm, Master Ccarton size: 570X330X370mm, Unit package: Gift paper box, Master Carton: Top cardboard carton |
Supply Ability: | 1000 Set/Sets per Month or to buyer's request |
Minimum Order Quantity: | 100 Set/Sets LOGO printing MOQ 100 units, OEM package MOQ 1000 units |
Payment Terms: | T/T,Western Union,MoneyGram,Paypal |
Port: | SHANGHAI or NINGBO |
FOB Price: | US $59 - 65 |
Length: | 80mm |
Sort: | Red laser sight, Laser sight, laser scope, led flashlight, led light |
Type: | Laser sight |
Color: | Matte balck or dark grey |
Material: | raft aluminum 7061-T6 |
Model Number: | XL-2LL-R |
Brand Name: | Buyer's logo |
Place of Origin: | China (Mainland) |