Neutral Stain Protection Treatment for Wooden Floors for Interiors

NEUTRAL STAIN PROTECTION TREATMENT FOR WOODEN FLOORS FOR INTERIORS
COMPOSITION
Teak oil, resin-wax emulsions, fluoropolymers, essences, water.
PROFILE
NATURAL PARQUET is a next generation product for the protection of indoor wooden floors. Completely colourless after application, it penetrates deeply into the wood fibres to make them impermeable to water, grease and stains, thanks to the size of the particles (fluorinated resins) and oil.
IMPORTANT: for regular cleaning, do not use alcohols, or acid, solvent or ammonia based-detergents.
INTENDED USE
The peculiarity of NATURAL PARQUET is to combine a natural end result without altering the tone of the wood while providing water, oil and dirt repellent properties. It can be used on common oak, teak, oak, fir, larch, elm, chestnut, walnut, etc...
INSTRUCTIONS
Shake well before use. Always use at temperatures above +10°C. Apply one coat of NATURAL PARQUET with a brush, fleece or applicator, applying it evenly and in generous amounts (approximately 12/17 sqm/l) with movements that are parallel to the grain of the wood. Wait for at least two hours. Then rub with abrasive mesh or sandpaper grade 280/320 to smooth the surface. Vacuum the dust. Apply another coat, in the same manner, but using less product (approximately 18/22 sqm/l). After 2 hours, if the wood grain is slightly raised, go over the surface with a single-brush floor cleaner fitted with a red disk. Then apply a third coat (approximately 20/25 sqm/l) using INDUR K-33 (see sheet). If you are working on brushed, smoothed or serrated surfaces, after the first coat of NATURAL PARQUET, when the surface is dry, simply go over with the single brush floor cleaner fitted with the green disk to lower the grain without sanding. You can complete the treatment with PRIMO LEGNO (our varnish). Always run some test applications before applying it to the definitive surfaces.
PROS
• Easy application.
• Creates a natural and soft finish.
• It does not release harmful substances during application or after.
• Maximum effectiveness after 6 days.
• Non-flammable.
• Easy to restore.
• Quick-drying.
• Very high resistance to light.
• Biodegradability above 90%.
• Suitable for oak, wengé, doussie, elm, larch, chestnut, etc...
• The treatment protects against water and oil.
• It does not release harmful substances during application or after.
• Delays ageing.
PROPERTIES
DILUTION: Ready for use.
DRYING: 24 hours.
WALKABLE: after 2 hours.
TIME OF REACTION: 6 days.
YIELD: Approximately 18-22 sqm/l per coat.
HOW TO CLEAN EQUIPMENT: Wash with soap and water.
STORAGE: Closed in the original packaging, in a cool place, away from frost and UV rays, it retains its properties for at least one year.
PACKAGING:
12 1-litre bottles
4 5-litre buckets
2 10-litre buckets
CHARACTERISTICS
APPEARANCE: liquid
COLOUR: milky
ODOUR: aromatic
PH (AT 20°C): 8.2
SOLUBILITY IN WATER: total.
SPECIFIC WEIGHT (20° C): 1.022 kg/l
VOC (Directive 2004/42/EC) :
Minimal build wood stains.
VOC given in g/litre of product in a ready-to-use condition :
Limit value: 130,00 (2010)
VOC of product : 60,68
HEALTH
The product is not classified as hazardous pursuant to the provisions set forth in EC Regulation 1272/2008 (CLP) (and subsequent amendments and supplements).
No danger symbol is required on the label It must nevertheless be kept out of the reach of children and must not be disposed of in drain water, in order to protect the environment. We nevertheless advise you to adopt good work practices.