Minerals & Metallurgy Manufacturers and Suppliers
Definition of raw materials graphite electrode Graphite electrode is high temperature resistant graphite conductive material. It is made of petroleum coke and pitch coke as aggregate and coal tar pitch as binder. The production process for metal making graphite electrode includes
Huaruo (Shanghai) Industrial Co., Ltd. [2022-06-13 16:24:28 ]
Description of Galvanized Rolled Steel Hot dipped galvanized steel sheet is a carbon steel sheet coated with zinc on both sides through a continuous hot-dip process. When the heated steel strip is in contact with the molten zinc, the coating is firmly adhered to the steel by the
Huaruo (Shanghai) Industrial Co., Ltd. [2022-06-13 16:23:53 ]
Description of Galvanized Steel Coils hot rolled galvanized steel coil are produced by passing the acid-washed and calendered full hard plate through the zinc tank, thereby galvanizing the film on the surface. Galvanized steel coil with good raw materials and 7 times the cold rol
Huaruo (Shanghai) Industrial Co., Ltd. [2022-06-13 16:23:22 ]
Description of Direct Reduced Iron (DRI Steel) Direct reduced iron (DRI), also called sponge iron, is produced from the direct reduction of iron ore (in the form of lumps, pellets, or fines) to iron by a reducing gas or elemental carbon produced from natural gas or coal. Many ore
Huaruo (Shanghai) Industrial Co., Ltd. [2022-06-13 16:22:46 ]
Description of Copper Cathode Copper is one of the basic chemical elements. In its nearly pure state, copper is a reddish-orange metal known for its high thermal and electrical conductivity. It is commonly used to produce a wide variety of products, including electrical wire, coo
Huaruo (Shanghai) Industrial Co., Ltd. [2022-06-13 16:22:00 ]
Name PPGI steel coil PPGL steel coil Standard EN/JIS/ASTM Grade DX51D Thickness 0.12-0.8mm (±0.01mm) Width 30-1250mm (±2mm) Length Coil or as Customers’ requirement Zinc/Aluzinc coating Zn 20g/sm-120g/sm Alu-zinc 30-70g/sm Coil weight max 10tons or As your requirement Hardnes
Shandong Liqiang Steel Plate Co.,Ltd [2022-06-07 09:27:17 ]
Our specification --Zinc Coating Z30-Z120/ AZ30-AZ70 --Top Side Coating according to customer\'s requirement --Back Side Coating according to customer\'s requirement --Thickness 0.13mm-0.8mm --Width below 1250mm --Color according to customer\'s requirement --Capacity 3 lin
Shandong Liqiang Steel Plate Co.,Ltd [2022-06-06 18:07:46 ]
Our specification --Spangle Zero Spangle or Min spangle --Zinc Coating Z30-Z120/ AZ30-AZ70 --Thickness 0.12mm-1.2mm --Width below 1250mm --Capacity 5 line with 1,500,000MT / Year 2. For PPGI & PPGL --Zinc Coating Z30-Z120/ AZ30-AZ70 --Top Side Coating according to customer
Shandong Liqiang Steel Plate Co.,Ltd [2022-06-06 18:01:08 ]
Standard ASTM, ANSI Place of Origin Guangdong, China Brand Name Z S.B Model Number SS-1 Type Seamless Steel Grade 300 Series, 301L, S30815, 301, 304N, 310S, S32305, 410, 204C3, 316Ti, 316L, 441, 316, L4, 420J1, 321, 410S, 410L, 436L, 443, LH, L1, S32304, 314, 347, 430, 309S, 304,
Shaanxi Z.S.B. Metal Products Co., Ltd. [2022-05-27 14:34:40 ]
Hybrid Bonded Magnetic Compounds Introductions： By mixing different kinds of magnetic powder in different proportions, we can obtain a series of hybrid magnets whose magnetic properties are higher than ferrite bonding magnet and lower than bonded neodymium (anisotropic) magnet,
Hangzhou Chase Technology Co., Ltd [2022-05-27 13:48:46 ]
Magnets and magnet assemblies have to meet increasingly complex requirements. Hard-Ferrite Bonded Magnetic Compounds Compared to rare earth magnetic materials, hard ferrites has obvious cost advantage due to the use of cheap strontium oxide, barium oxide and iron oxide as raw mat
Hangzhou Chase Technology Co., Ltd [2022-05-27 13:47:42 ]
Introduction SmFeN magnetic material uses abundant rare-earth Sm element instead of expensive elements of Nd, Dy, Co, etc, and is the most cost-effective rare earth permanent magnetic material. Compared with the bonded neodymium magnet, the bonded SmFeN magnet has higher magnetic
Hangzhou Chase Technology Co., Ltd [2022-05-27 13:45:53 ]
Item CuZn5 Brass Foil Standard ASTM, AISI, JIS, ISO, EN, BS, GB, etc. Material H70, H68, H65, H63, H62, H96, H90, H85, H80, CuZn30, CuZn33, CuZn36, CuZn37, CuZn5, CuZn10, CuZn15, CuZn20, CZ106, CZ107, CZ108, CZ109, CZ125, CZ101, CZ102, CZ103, C2600, C2700, C2720, C2800, C2100, C2
Buck Copper Group [2022-05-26 10:38:32 ]
Application of spiral welded pipe 1. Water supply engineering 2. Petrochemical industry 3. Chemical industry 4. Electric power industry 5. Agricultural irrigation 6. Urban construction. 7. Water supply and drainage. 8. Gas transport 9. Structure construction
Bestar Steel Co., Ltd. [2022-05-26 08:56:34 ]
Sapphire ingots are typically used as raw materials for further processing. These sapphire rods and sapphire ingots are uniformly shaped, usually as cylinders. The most sapphire crystal grows in A-axis, and the most widely used sapphire substrate in the LED market is its C-plane
CRYSCORE OPTOELECTRONIC LIMITED [2022-05-25 15:31:17 ]
Aluminum Wire Supplier Yurui is one of reliable and professional aluminum wire manufacturers that has many years of experience supplying aluminum products, and so far no bad feedbacks. Besides aluminum wire, we can also offer other aluminum products such as aluminum blocks, alumi
Jiangyin Yurui Metallurgical Material Co., Ltd. [2022-05-24 15:38:35 ]
During the technology of steelmaking, We add some aluminum products to the bearing steel and carbon molten steel to achieve the requirements of deoxidization, such as steel-cored aluminum, aluminum block, and aluminum granule. It can refine grain, restrain the aging of carbon ste
Jiangyin Yurui Metallurgical Material Co., Ltd. [2022-05-24 15:37:38 ]
Aluminum granules are refined by repeated drawing, cutting, and grinding of 99.5 aluminum ingot. Bright appearance, cylindrical, applied to the surface of aluminum, zinc, or thin-walled workpiece. It is widely used in the surface finishing of ferro aluminum castings, copper and z
Jiangyin Yurui Metallurgical Material Co., Ltd. [2022-05-24 15:36:47 ]
Aluminum granules are refined by repeated drawing, cutting, and grinding of 99.5 aluminum ingot. Bright appearance, cylindrical, applied to the surface of aluminum, zinc, or thin-walled workpiece. It is widely used in the surface finishing of aluminum castings, copper and zinc ca
Jiangyin Yurui Metallurgical Material Co., Ltd. [2022-05-24 15:36:02 ]
The 99 aluminum block has better conductivity, ductility, reflectance and corrosion resistance. It can be applied to high purity sputtering targets for semiconductor wiring, semiconductor packaging, flat panel display, solar cell, high entropy alloy and evaporation coating, cemen
Jiangyin Yurui Metallurgical Material Co., Ltd. [2022-05-24 15:35:04 ]
