Cable Length;2m Technical specifications \? (Max. Range) 4.5 mm !
High performance electronic beam switch High performance electronic beam switch Wide input power voltages from 24 to 240V ac or dcFast response time less than 20ms Easy installation
Druckbereich Genauigkeit Anwendung Merkmale DMP 343 Druckbereich Genauigkeit Anwendung Merkmale von 10 mbar bis 1000 mbar von 0,175% bis 0,25% FSO BFSL / von 0,35% bis 0,5 % FSO IEC 60770 Pneumatik, Vakuumtechnik, Medizintechnik, Filtertechnik mechanisch G1/2", G1/4"elektrisch IS
Mounting brackets and flanges Measuring arms, pedestals and toothed-wheels
Met One 010C Ranges Starting speed Accuracy Temp/Ranges Met One 010C 0-125 mph or0-60meters/second 0.5 mph or .22 meters/second
Compact Amplifier-contained but compact. Amplifier-Contained Compact Cylindrical Proximity Sensors
Load Washer, Thru hole Load cell, Tool Steel. 20 t - 500 t The 296W series are washer shaped, strain gage based load cells that have been most commonly used in fastener testing and thru hole load applications These load cells are manufactured from heat treated tool steel and are
High power UHF phone transmitter. When the phone is in use both sides of the conversation are transmitted to a receiver. Excepti High power UHF phone transmitter. When the phone is in use both sides of the conversation are transmitted to a receiver. Exceptional audio quality Feat
Triple Point Temperature Sensors allow monitoring of three separate temperature points within a vessel using a single probe. Ori Triple Point Temperature Sensors allow monitoring of three separate temperature points within a vessel using a single probe. Originally designed by Con
A single NDB transmitter, intended for installation where lower powers single NDB transmitter, intended for installation where lower powers are both sufficient and desirable at offshore platforms. TS-20B/s is a single transmitter just 60cm high and weight approx. 20kg, it may eas
The 330450 HTAS segregates the sensing element from the signal conditioning electronics The 330450 HTAS segregates the sensing element from the signal conditioning electronics, with the two permanently connected via a hard-line cable. This allows the sensing head to be mounted on
Photo IC for Optical Link Photo IC receivers and emitters for plastic optical fiber communications. Our receiver line-up includes monolithic IC devices integrated with a PIN photodiode and analog amplifier.
probe with mounting flange or bulkhead fitting and plastic, galvanized steel Five installations options probe with mounting flange or bulkhead fitting and plastic, galvanized steel, or NEMA-4/IP-65 enclosure offer the industrysmost extensive range to satisfy all HVAC,appliance an
Thermal Sensors - Low Powers to 50W Thermal Sensors - Low Powers to 50WOphir has the widest selection of heads for low average powers in the industry. From the popular 3A series that can reliably measure down to tens of microwatts and microjoules to the L50A for up to 50W continu
cut out temperatures available from 20C to 150C, differential of 10C max, 10W switching capability. Normally closed (NC), cut out temperatures available from 20C to 150C, differential of 10C max, 10W switching capability.
Z4A - Force standard 2 Nominal sensitivity [mV/V] 20 kN, 50 kN, 100 kN, 200 kN, 500 kN Nominal force tensile / compressive Direction of force tempered steel Material IP 67 Protection system +10...+40 Nominal temp. range [
Typically, a 0.005" (125m) polyester layer is laminated to a 28m piezo fi lm element. When used in a "bend ing" mode Description (nF) Part No. 1 10 100 Part No. LDT0-028K, with Solder Tabs .500 MSP1006-ND 1.80 1.35 .75 1002794-0 LDTM-028K, with Mass and Solder Tabs .420 MSP1007-N
