Silicone Potting Compound for electronic component for LED drivers and electronic component

Minimum Order
1
Packaging
N/A
Delivery
15 Days

Before The Curing

Performance Indicators A B
Appearance Gray Fluid White Fluid
Viscosity 1500~2500(cps) 1500~2500(cps)
A:B 1:1
Mixed Viscosity 1500~2500(cps)
Operable Time 30~120(min) (Adjustable)
Curing Time 3~5(h)



After The Curing

Hardness 40~50(Shore A)
Dielectric Strength ≥20(kV/mm)
Dielectric Constant 3.12(1.2MHz)
Thermal Conductivity ≥0.6[W/m.k]
Volume Resistivity ≥1.0×1014(Ω·cm)
Specific Gravity 1.56±0.02(g/cm3)
Flammability Rating UL94 V-0



•20kg/set(A10kg+B10kg), packaging with bucket.




Preparing: Stir completely A and B in each container,

Mixing:A and B should be fully mixed according to the weighting ratio. Add B to A. Stirring(stir the glue dedicated blade) and mixing. Note that: should be mixedthoroughly when mixing the wall rubber of container into the plastic material.

De-airing: after mixing which should vacuum degassing for 1-3 minutes.

Potting: The mixture should be poured into the product as soon as possible, in order to avoid thickening and resulting in poor fluidity.

Curing: Heat curing or at room temperature curing. The higher the temperature, the quicker curing . The temperature is low, the curing time will be extended either. In winter, it will take a long time to cure, so suggest that heating curing. It is cured for 15 minutes at 80 ° C ~ 100 ° C, about 12 hours at room temperature.



MATTERS NEEDING ATTENTION

NOTE

1,The mixture should be sealed and stored in a dry environment at room temperature, and should be used as soon as possible, to avoid wastage.

2,The product don’t belong to dangerous goods, but avoid contacting skin and eyes.

3,The product is non-toxic, has good physical inertia without stimulation and harm. The product does not contain flammable and explosive ingredients which will not cause fire or explosion without special requirement for transport.

4,Stored for a period of time, the plastic may be layered. So please stir well before using, and can’t affect its performance.

5,The following substances may hinder the curing or cause the phenomenon of not cure, so it is used after simple experiments, and need to clean the site of application if necessary.

A, incompletely cured condensation type silicone rubber.

B.amine (amine) curable epoxy resin.

C. ash welding (solder-flux).

SPECIFICATION TRANSPORT

PACKAGING

1,20kg/set(A10kg+B10kg), packaging with bucket.

2,1 year shelf life if stored below 25 ℃, when the product passed its expiration date, it should be confirmed without abnormal phenomenon, then that can be used.

3,These products don\'t belong to dangerous goods, so they can be transported as normal chemicals. But be careful of leakage.

  • Country: China (Mainland)
  • Business Type: 生产厂家
  • Market:美洲,欧洲,欧洲联盟
  • Founded Year:2001
  • Address:
  • Contact:Joe Lu
more images of Silicone Potting Compound for electronic component for LED drivers and electronic component
*Your name:
*Your Email:
*To:Guangzhou Usilicone chemical material Co.,Ltd
*Subject:
*Message:
Enter between 20 to 3,000 characters. English only.     Characters : 0 / 3000
*Enter the secure code shown below Mfrbee security Image      Reload Image

submiting now We do inquire for you , please wait ...

Silicone Potting Compound with good anti-aging for LED drivers and electronic component
Silicone Potting Compound with good anti-aging for LED drivers and electronic component

Before The Curing Performance Indicators  A B Appearance Gray Fluid White Fluid Viscosity  1500~2500(cps) 1500~2500(cps) A:B  1:1 Mixed Viscosity  1500~2500(cps) Operable Time 30~120(min) (Adjustable) Curing Time 3~5(h) After The Curing  Hardness  40~50(Shore A) ...

Guangzhou Usilicone chemical material Co.,Ltd